TVS Diode Arrays (SPA ? Diodes)
General Purpose ESD Protection - SP723 Series
Absolute Maximum Ratings
Thermal Information
C/W
C/W
C
Parameter
Continuous Supply Voltage, (V+) - (V-)
Forward Peak Current, I IN to V CC , I IN to
GND (Refer to Figure 5)
Peak Pulse Current, 8/20μs
Rating
+35
±4, 100μs
±7
Units
V
A
A
Parameter
Thermal Resistance (Typical, Note 1)
PDIP Package
SOIC Package
Storage Temperature Range
Rating
θ JA
160
170
-65 to 150
Units
o C/W
o
o
o
C
C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress only rating and operation of the device
at these or any other conditions above those indicated in the operational sections of this
specification is not implied.
Note:
Maximum Junction Temperature (Plastic
Package)
Lead Temperature
(Soldering 20-40s) (SOIC Lead Tips Only)
150
260
o
o
ESD Ratings and Capability (Figure 1, Table 1)
Load Dump and Reverse Battery (Note 2)
1. θ JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Characteristics
T A = -40 o C to 105 o C, V IN = 0.5V CC , Unless Otherwise Specified
Parameter
Operating Voltage Range,
V SUPPLY =[(V+)-(V-)]
Symbol
V SUPPLY
Test Conditions
Min
-
Typ
2 to 30
Max
-
Units
V
Forward Voltage Drop
IN to V-
V FWDL
I IN =2A(Peak Pulse)
-
2
-
V
IN to V+
Input Leakage Current
Quiescent Supply Current
Equivalent SCR ON Threshod
Equivalent SCR ON Resistance
Input Capacitance
Input Switching Speed
V FWDH
I IN
I QUIESCENT
C IN
t ON
Note 3
V FWD /I FWD ; Note 3
-
-20
-
-
-
-
-
2
5
50
1.1
0.5
5
2
-
20
200
-
-
-
-
V
nA
nA
V
Ω
PF
ns
Notes:
2. In automotive ans battery operated systems, the power supply lines should be externally protected for load dump and reverse battery. When the V+ and V- Pins are connected to the same
supply voltage source as the device or control line under protection, acurrent limiting resistor should be connectied in series between the external supply and the SP723 supply pins to
limit reverse battery current to within the rated maximum limits. Bypass capacitors of typically 0.01μF or larger from the V+ and V- Pins to ground are recommended.
3. Refer to the Figure 3 graph for determine peak current and dessipation under EOS conditions.
Typical Application of the SP723
(Application as an Input Clamp for Over-voltage, Greater than 1V BE
Above V+ or less than -1V BE below V-)
+V CC
INPUT
DRIVERS
OR
SIGNAL
SOURCES
+V CC
LINEAR OR
DIGITAL IC
INTERFACE
IN 1 - 3
IN 5 - 7
TO +V CC
V+
SP723
V-
SP723 INPUT PROTECTION CIRCUIT (1 OF 6 SHO WN)
FIGURE 4. TYPICAL APPLICA TION OF THE SP723 AS AN INPUT CLAMP FOR OVER-VOLTAGE, GREATER THAN 1V BE ABOVE V+ OR
LESS THAN -1V BE BELO W V-
? 2013 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 04/24/13
相关PDF资料
SP724AHTG TVS ARRAY ESD 4 INPUT SOT-23
SP724AHT TVS ARRAY ESD 4 INPUT SOT-23
SPC02SVDN-RC CONN JUMPER SHORTING .100" GOLD
SPC02SVGN-RC CONN JUMPER SHORTING .100" GOLD
SPC02SVJN-RC CONN JUMPER SHORTING .100" GOLD
SPC02SVKN-RC CONN JUMPER SHORTING .100" GOLD
SPC02SXCN-RC CONN JUMPER SHORTING .100" GOLD
SPC02SXIN-RC CONN JUMPER SHORTING .100" GOLD
相关代理商/技术参数
SP723APP 制造商:Littelfuse 功能描述:THYRISTOR ARRAY TVS
SP724AHT 功能描述:TVS二极管阵列 20V 2.2A RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C
SP724AHTG 功能描述:TVS二极管阵列 20V 2.2A 4 CHANNEL RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C
SP724AHTG 制造商:Littelfuse 功能描述:TVS ARRAYESD4 INPUTSOT23-6
SP724AHTG-CUT TAPE 制造商:LITTELFUSE 功能描述:SP724 Series 3 pF Surface Mount SCR & Diode Rail Clamp Array - SOT-23-6
SP724AHTP 功能描述:TVS二极管阵列 20V 2.2A RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C
SP724AHTP 制造商:Littelfuse 功能描述:TVS Diode Array
SP725 制造商:LITTELFUSE 制造商全称:Littelfuse 功能描述:Lead-Free/Green Series